Cisco Exam 200-301 Topic 6 Question 99 Discussion

Actual exam question for Cisco's 200-301 exam

Question #: 99
Topic #: 6

SIMULATION

All physical cabling between the two switches is installed. Configure the network connectivity between the switches using the designated VLANs and interfaces.

1. Configure VLAN 100 named Compute and VLAN 200 named Telephony where required for each task.

2. Configure Ethernet0/1 on SW2 to use the existing VLAN named Available.

3. Configure the connection between the switches using access ports.

4. Configure Ethernet0/1 on SW1 using data and voice VLANs.

5. Configure Ethemet0/1 on SW2 so that the Cisco proprietary neighbor discovery protocol is turned off for the designated interface only.

ASee the Explanation below

Show Suggested Answer

Suggested Answer: A

Answer as below configuration:

on sw1

enable

conf t

vlan 100

name Compute

vlan 200

name Telephony

int e0/1

switchport voice vlan 200

switchport access vlan 100

int e0/0

switchport mode access

do wr

on sw2

Vlan 99

Name Available

Int e0/1

Switchport access vlan 99

do wr

by Paz at Oct 22, 2024, 03:18 AM

Limited Time Offer

25%

Off

Get Premium 200-301 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Veronica

5 months ago

This looks like a nice, juicy configuration question. Time to put my networking skills to the test!

upvoted 0 times

...

Gilbert

5 months ago

Haha, I bet the exam writers just threw in that Cisco protocol thing to trip us up. Nice try, but I'm on to you!

upvoted 0 times

Keena

4 months ago

Let's make sure we double-check everything to be safe.

upvoted 0 times

...

Otis

4 months ago

Yeah, but we're prepared for anything they throw at us.

upvoted 0 times

...

Tamera

4 months ago

I know right, they always try to trick us with those tricky details.

upvoted 0 times

...

Shayne

5 months ago

Wait, we need to turn off the Cisco neighbor discovery protocol on Ethernet0/1 on SW2? That's a bit random, but okay, I'll make sure to do that.

upvoted 0 times

Freeman

4 months ago

Micaela: I'll keep that in mind, thanks for the reminder.

upvoted 0 times

...

Alexia

4 months ago

User 3: Make sure to follow all the steps for configuring the network connectivity between the switches.

upvoted 0 times

...

Micaela

4 months ago

User 2: Yeah, that's a specific requirement for that interface.

upvoted 0 times

...

Chandra

5 months ago

User 1: Did you see we need to turn off the Cisco neighbor discovery protocol on Ethernet0/1 on SW2?

upvoted 0 times

...

Rosalyn

6 months ago

Hmm, seems straightforward. Just need to configure the VLANs and interfaces correctly. Should be able to knock this one out.

upvoted 0 times

Yuriko

4 months ago

Steffanie: After that, we can configure Ethernet0/1 on SW1 using data and voice VLANs.

upvoted 0 times

...

Kattie

4 months ago

User 3: Next, we need to configure the connection between the switches using access ports.

upvoted 0 times

...

Steffanie

5 months ago

User 2: Got it. I'll also configure Ethernet0/1 on SW2 to use the existing VLAN named Available.

upvoted 0 times

...

Tanesha

5 months ago

User 1: Let's start by configuring VLAN 100 named Compute and VLAN 200 named Telephony.

upvoted 0 times

...

Gail

6 months ago

I believe we should turn off the Cisco proprietary neighbor discovery protocol on SW2.

upvoted 0 times

...

Kina

6 months ago

I agree, we also need to configure the connection between the switches using access ports.

upvoted 0 times

...

Nina

6 months ago

I think we need to configure VLANs 100 and 200 for this task.

upvoted 0 times

...