Independence Day Deal! Unlock 25% OFF Today – Limited-Time Offer - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location PL
Mob_nav_barsMENU

Oracle Exam 1Z0-821 Topic 4 Question 73 Discussion

Actual exam question for Oracle's 1Z0-821 exam
Question #: 73
Topic #: 4
[All 1Z0-821 Questions]

On server A, you enter the following command to add a static route to serverA route -p add -host 192.168.1.101 192.168.1.101 -static

What is the purpose of this command?

Show Suggested Answer Hide Answer
Suggested Answer: B, D, E

B: By carrying SCSI commands over IP networks, the iSCSI protocol enables you to access block devices from across the network as if they were connected to the local system. COMSTAR provides an easier way to manage these iSCSI target devices.

D: Common Multiprotocol SCSI TARget, or COMSTAR, a software framework that enables you to convert any Oracle Solaris 11 host into a SCSI target device that can be accessed over a storage network by initiator hosts.

E: One IP port can handle multiple iSCSI target devices.


by Leatha at Oct 19, 2023, 08:29 PM

Limited Time Offer

25%

Off

Get Premium 1Z0-821 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel
Haley
2 months ago
This one's a classic! C is the answer, no doubt. Though I did have a moment where I thought it might be to optimize my link aggregation. The joys of server administration.
upvoted 0 times
Shantell
29 days ago
Yeah, it's always good to double check the purpose of commands in server administration.
upvoted 0 times
...
Daisy
1 months ago
I was also considering F for optimizing link aggregation, but C makes more sense now.
upvoted 0 times
...
Bobbie
1 months ago
I agree, it's definitely to specify routing to an adjacent network when in.rdisc is not used.
upvoted 0 times
...
Tanja
2 months ago
I think C is the correct answer.
upvoted 0 times
...
...
Mitsue
2 months ago
Haha, the options are a bit tricky, but I'm pretty sure C is the way to go. No need to route around any IP filters or ARP caches here.
upvoted 0 times
...
Narcisa
2 months ago
I was a bit confused between C and D, but I'm confident C is the right answer now. Good one!
upvoted 0 times
Erick
1 months ago
Yeah, it makes sense to specify routing to an adjacent network when in.rdisc is not used.
upvoted 0 times
...
Sabina
1 months ago
I think C is the correct answer too.
upvoted 0 times
...
Celestina
2 months ago
User 2: Yeah, I agree. It's definitely not to temporarily bypass IP Filter rules.
upvoted 0 times
...
Adelina
2 months ago
User 1: I think the purpose of that command is to specify routing to an adjacent network when in.rdisc is not used.
upvoted 0 times
...
...
Karl
2 months ago
I think the correct answer is C. The command is used to specify routing to an adjacent network when in.rdisc is not used.
upvoted 0 times
Lenna
25 days ago
D) to specify routing to an adjacent network when in.routed is not used
upvoted 0 times
...
Heidy
1 months ago
C) to specify routing to an adjacent network when in.rdisc is not used
upvoted 0 times
...
Eva
1 months ago
B) to specify an IPMP target IP address to in.mpathd
upvoted 0 times
...
Larae
1 months ago
A) to temporarily bypass IP Filter rules
upvoted 0 times
...
...
Gerry
3 months ago
But what about option A, could it be to temporarily bypass IP Filter rules instead?
upvoted 0 times
...
Rory
3 months ago
I agree with Madonna, it makes sense to add a static route in that scenario.
upvoted 0 times
...
Madonna
3 months ago
I think the purpose of this command is to specify routing to an adjacent network when in.routed is not used.
upvoted 0 times
...

Save Cancel
az-700  pass4success  az-104  200-301  200-201  cissp  350-401  350-201  350-501  350-601  350-801  350-901  az-720  az-305  pl-300  

Warning: Cannot modify header information - headers already sent by (output started at /pass.php:70) in /pass.php on line 77