Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location PL
Mob_nav_barsMENU

NetApp Exam NS0-593 Topic 1 Question 65 Discussion

Actual exam question for NetApp's NS0-593 exam
Question #: 65
Topic #: 1
[All NS0-593 Questions]

After a motherboard replacement on a NetApp AFF A300 in a SAN environment, the customer states that ports 0e and 0f are unable to connect to the fabric. The ports report "offline".

What would you examine first to troubleshoot the issue?

Show Suggested Answer Hide Answer
Suggested Answer: B

Here is my reasoning:

Thesystem node hardware unified-connect showcommand displays the status and configuration of the Unified Connect ports on a node1. This command can help you identify if the ports are configured correctly and if they have any errors or faults.

The ports 0e and 0f on the AFF A300 are 10GbE ports that support both Ethernet and Fibre Channel over Ethernet (FCoE) protocols2.These ports are part of the Unified Connect feature, which enables you to use the same physical port for different protocols without requiring additional hardware3.

If the ports are offline, it could indicate a problem with the port configuration, the cable connection, the switch configuration, or the protocol settings.Thesystem node hardware unified-connect showcommand can help you troubleshoot these issues by showing you the port mode, speed, duplex, state, and error count1.

The other commands in the options are not as helpful for troubleshooting the port issue, because they show different information that is not related to the Unified Connect feature or the port status. For example:

Thevserver fcp wwpn-alias showcommand displays the World Wide Port Name (WWPN) aliases for the Fibre Channel Protocol (FCP) logical interfaces (LIFs) on a Vserver4. This command can help you manage the FCP LIFs, but it does not show the status of the physical ports or the Unified Connect feature.

Thestorage port showcommand displays the status and configuration of the storage ports on a node5. This command can help you manage the storage ports, but it does not show the status of the Unified Connect ports or the FCoE protocol.

Thevserver fcp interface showcommand displays the status and configuration of the FCP LIFs on a Vserver6. This command can help you manage the FCP LIFs, but it does not show the status of the physical ports or the Unified Connect feature.

Here are some references that might help you:

1:system node hardware unified-connect show - NetApp2:AFF A300 system installation - NetApp3:Unified Connect - NetApp4:vserver fcp wwpn-alias show - NetApp5:storage port show - NetApp6:vserver fcp interface show - NetApp


by Cory at Feb 05, 2025, 11:33 PM

Limited Time Offer

25%

Off

Get Premium NS0-593 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel
Cassie
2 months ago
C all the way! If the ports are offline, the storage port show is where you'll find the root of the problem. Easy peasy.
upvoted 0 times
...
Glen
2 months ago
Ah, a classic NetApp troubleshooting question. I'd start with C, because you can't connect to the fabric if the ports are down.
upvoted 0 times
...
Elke
2 months ago
Option C is the way to go. I bet the storage port show command will give you the information you need to figure this out.
upvoted 0 times
...
Arthur
2 months ago
I agree with C. Checking the storage port status is the logical first step in this scenario.
upvoted 0 times
Tegan
24 days ago
Good point, let's gather all the necessary information before proceeding.
upvoted 0 times
...
Lorriane
25 days ago
I think we should also look at the vserver fcp interface show command output.
upvoted 0 times
...
Stevie
26 days ago
Once we have that information, we can move on to the next steps.
upvoted 0 times
...
Louvenia
28 days ago
Agreed, that's the best place to start troubleshooting.
upvoted 0 times
...
Dulce
1 months ago
Agreed, that's the best place to start troubleshooting.
upvoted 0 times
...
Kirk
1 months ago
Let's check the storage port show command output first.
upvoted 0 times
...
Michell
1 months ago
Let's check the storage port show command output first.
upvoted 0 times
...
...
Gilma
2 months ago
Definitely go with C. If the ports are reporting as offline, you need to check the storage port status first to see what's going on.
upvoted 0 times
Derick
2 months ago
Once we have that information, we can further troubleshoot the issue.
upvoted 0 times
...
Luisa
2 months ago
I agree, checking the storage port status is the first step.
upvoted 0 times
...
...
Carin
2 months ago
I would also consider looking at the storage port show command output to see if there are any issues with the ports themselves.
upvoted 0 times
...
Olive
2 months ago
I agree with Almeta. Checking the vserver fcp wwpn-alias show command output could help identify the issue with ports 0e and 0f.
upvoted 0 times
...
Almeta
2 months ago
I think I would examine the vserver fcp wwpn-alias show command output first.
upvoted 0 times
...
Melvin
2 months ago
I think the correct answer would be C) storage port show command output. That's the first thing I'd check to see the status of the ports.
upvoted 0 times
Jaclyn
1 months ago
User 4: Hopefully we can troubleshoot the issue quickly with that information.
upvoted 0 times
...
Cornell
1 months ago
User 3: I agree, let's see if that gives us any clues on why they're offline.
upvoted 0 times
...
Shizue
1 months ago
User 2: Yeah, that's a good place to start to see the status of the ports.
upvoted 0 times
...
Dona
2 months ago
User 1: I would check the storage port show command output first.
upvoted 0 times
...
...

Save Cancel
az-700  pass4success  az-104  200-301  200-201  cissp  350-401  350-201  350-501  350-601  350-801  350-901  az-720  az-305  pl-300  

Warning: Cannot modify header information - headers already sent by (output started at /pass.php:70) in /pass.php on line 77