Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location PL
Mob_nav_barsMENU

NetApp Exam NS0-593 Topic 1 Question 47 Discussion

Actual exam question for NetApp's NS0-593 exam
Question #: 47
Topic #: 1
[All NS0-593 Questions]

Refer to the exhibit.

Referring to the exhibit, what do you need to do to return the MetroCluster to a normal state?

Show Suggested Answer Hide Answer
Suggested Answer: B

Here is my reasoning:

Thesystem node hardware unified-connect showcommand displays the status and configuration of the Unified Connect ports on a node1. This command can help you identify if the ports are configured correctly and if they have any errors or faults.

The ports 0e and 0f on the AFF A300 are 10GbE ports that support both Ethernet and Fibre Channel over Ethernet (FCoE) protocols2.These ports are part of the Unified Connect feature, which enables you to use the same physical port for different protocols without requiring additional hardware3.

If the ports are offline, it could indicate a problem with the port configuration, the cable connection, the switch configuration, or the protocol settings.Thesystem node hardware unified-connect showcommand can help you troubleshoot these issues by showing you the port mode, speed, duplex, state, and error count1.

The other commands in the options are not as helpful for troubleshooting the port issue, because they show different information that is not related to the Unified Connect feature or the port status. For example:

Thevserver fcp wwpn-alias showcommand displays the World Wide Port Name (WWPN) aliases for the Fibre Channel Protocol (FCP) logical interfaces (LIFs) on a Vserver4. This command can help you manage the FCP LIFs, but it does not show the status of the physical ports or the Unified Connect feature.

Thestorage port showcommand displays the status and configuration of the storage ports on a node5. This command can help you manage the storage ports, but it does not show the status of the Unified Connect ports or the FCoE protocol.

Thevserver fcp interface showcommand displays the status and configuration of the FCP LIFs on a Vserver6. This command can help you manage the FCP LIFs, but it does not show the status of the physical ports or the Unified Connect feature.

Here are some references that might help you:

1:system node hardware unified-connect show - NetApp2:AFF A300 system installation - NetApp3:Unified Connect - NetApp4:vserver fcp wwpn-alias show - NetApp5:storage port show - NetApp6:vserver fcp interface show - NetApp


by Wilford at Jun 03, 2024, 06:48 AM

Limited Time Offer

25%

Off

Get Premium NS0-593 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel
Eric
16 days ago
I'm not sure if C or D would work, since the question specifically mentions returning the MetroCluster to a normal state, not just giving back storage.
upvoted 0 times
...
Altha
17 days ago
B seems to be the correct answer. The MetroCluster needs to be switched back to its normal state, and that would involve the metrocluster switchback command on Site A.
upvoted 0 times
...
Jamika
18 days ago
Hmm, I see your point. Let's review the exhibit again to confirm.
upvoted 0 times
...
Almeta
20 days ago
I disagree, I believe the correct answer is D) Enter the storage failover giveback command on Site A.
upvoted 0 times
...
Jamika
22 days ago
I think the answer is B) Enter the metrocluster switchback command on Site A.
upvoted 0 times
...

Save Cancel
az-700  pass4success  az-104  200-301  200-201  cissp  350-401  350-201  350-501  350-601  350-801  350-901  az-720  az-305  pl-300  

Warning: Cannot modify header information - headers already sent by (output started at /pass.php:70) in /pass.php on line 77