HP Exam HPE6-A72 Topic 4 Question 53 Discussion

Actual exam question for HP's HPE6-A72 exam

Question #: 53
Topic #: 4

[All HPE6-A72 Questions]

Interface 1/1/1 is up

Admin state is up

Link transitions: 1

Description: TO_PC-1

Hardware: Ethernet, MAC Address: 00:11:22:33:44:55

MTU 1500

Type 1GbT

Full-duplex

qos trust none

Speed 1000 Mb/s

Auto-negotiation is on

Flow-control: off

Error-control: off

MDI mode: MDIX

VLAN Mode: access

Access VLAN: 1111

Which command will produce the above output?

Ashow interface vlan 1111

Bshow interface 1/1/1

Cshow interface gigabit 1/1/1

Dshow vlan 1111

Show Suggested Answer

Suggested Answer: A

by Kristel at Nov 26, 2023, 04:47 AM

Limited Time Offer

25%

Off

Get Premium HPE6-A72 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Ettie

1 months ago

I wonder if the interface is up because it's connected to a PC-1. Maybe the IT guy has a good sense of humor. Anyway, B) is the answer!

upvoted 0 times

...

Lavonna

1 months ago

A) show interface vlan 1111 doesn't sound right, since the output doesn't mention anything about a VLAN interface. B) is the way to go!

upvoted 0 times

Luisa

12 days ago

A) show interface vlan 1111 doesn't sound right, since the output doesn't mention anything about a VLAN interface. B) is the way to go!

upvoted 0 times

...

Lorean

17 days ago

B) show interface 1/1/1

upvoted 0 times

...

Arminda

2 months ago

Hmm, I'm not sure if C) show interface gigabit 1/1/1 would work, since the output doesn't mention 'gigabit' explicitly. I'll go with B) to be safe.

upvoted 0 times

Matthew

3 days ago

User 2: I agree, let's go with B) to be safe.

upvoted 0 times

...

Jordan

4 days ago

User 1: I think B) show interface 1/1/1 is the right command to use.

upvoted 0 times

...

Felicidad

2 months ago

The output gives a lot of details about the interface, including the VLAN configuration, so I'm going with B) show interface 1/1/1.

upvoted 0 times

Jamal

8 hours ago

I knew it! The output was very specific.

upvoted 0 times

...

Kenny

3 days ago

That's correct! It provides detailed information about the interface.

upvoted 0 times

...

Albina

17 days ago

B) show interface 1/1/1

upvoted 0 times

...

Lashaunda

23 days ago

Yes, that command will display all the details about interface 1/1/1, including the VLAN configuration.

upvoted 0 times

...

Tequila

1 months ago

I think B) show interface 1/1/1 is the correct command to produce that output.

upvoted 0 times

...

Malcom

1 months ago

Yes, that's right. It provides all the details about the interface including the VLAN configuration.

upvoted 0 times

...

Tequila

1 months ago

I think the correct command is B) show interface 1/1/1

upvoted 0 times

...

Sue

2 months ago

This is a straightforward interface status command. I think the correct answer is B) show interface 1/1/1.

upvoted 0 times

Tori

11 days ago

It just takes practice to remember them all.

upvoted 0 times

...

Mireya

17 days ago

I always get confused with these commands.

upvoted 0 times

...

Annett

25 days ago

That's correct!

upvoted 0 times

...

Mona

1 months ago

B) show interface 1/1/1

upvoted 0 times

...

Domonique

2 months ago

I'm not sure, but I think C) show interface gigabit 1/1/1 could also be a possible answer

upvoted 0 times

...

Leatha

2 months ago

I agree with Maricela, because the output mentions interface 1/1/1

upvoted 0 times

...

Maricela

2 months ago

I think the answer is B) show interface 1/1/1

upvoted 0 times

...