Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location PL
Mob_nav_barsMENU

Fortinet Exam NSE7_EFW-7.2 Topic 5 Question 37 Discussion

Actual exam question for Fortinet's NSE7_EFW-7.2 exam
Question #: 37
Topic #: 5
[All NSE7_EFW-7.2 Questions]

Refer to the exhibit, which contains a partial BGP combination.

You want to configure a loopback as the OGP source.

Which two parameters must you set in the BGP configuration? (Choose two)

Show Suggested Answer Hide Answer
Suggested Answer: A, D

To configure a loopback as the BGP source, you need to set the ''ebgp-enforce-multihop'' and ''update-source'' parameters in the BGP configuration.The ''ebgp-enforce-multihop'' allows EBGP connections to neighbor routers that are not directly connected, while ''update-source'' specifies the IP address that should be used for the BGP session1.Reference:=BGP on loopback,Loopback interface,Technical Tip: Configuring EBGP Multihop Load-Balancing,Technical Tip: BGP routes are not installed in routing table with loopback as update source


by Aleshia at May 03, 2025, 08:51 PM

Limited Time Offer

25%

Off

Get Premium NSE7_EFW-7.2 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel
Octavio
4 days ago
Hmm, let me think... Ah, I got it! D) update-source, of course. Gotta love these tricky BGP questions.
upvoted 0 times
...
Mira
8 days ago
This is a classic BGP configuration question. D) update-source is the solution, no doubt about it.
upvoted 0 times
...
Margery
11 days ago
Ah, the old BGP loopback source trick. D) update-source is the only logical choice here. Time to impress the examiners!
upvoted 0 times
Tamra
9 days ago
User 1: I think D) update-source is the correct parameter to set.
upvoted 0 times
...
...
Graham
28 days ago
Haha, I bet the poor exam taker is scratching their head on this one. But D) update-source is the way to go!
upvoted 0 times
Hermila
2 days ago
I think C) ibgp-enforce-multihop is also necessary for the BGP configuration.
upvoted 0 times
...
Pete
4 days ago
Don't forget about A) ebgp-enforce-multihop as well, it's important for setting up the loopback.
upvoted 0 times
...
James
5 days ago
Agreed, D) update-source is definitely needed for configuring a loopback as the BGP source.
upvoted 0 times
...
...
Alison
1 months ago
I believe the correct options are A) ebgp-enforce-multihop and D) update-source.
upvoted 0 times
...
Deangelo
1 months ago
Definitely D) update-source. I've seen this type of question before, and that's the key to configuring the BGP source interface.
upvoted 0 times
Maryln
16 hours ago
I think the other parameter you need to set is A) ebgp-enforce-multihop.
upvoted 0 times
...
Claudia
12 days ago
I agree, D) update-source is definitely one of the parameters you need to set.
upvoted 0 times
...
...
Jillian
1 months ago
I agree with Shanda, setting the update-source parameter makes sense.
upvoted 0 times
...
Danilo
2 months ago
Hmm, the correct answer has to be D) update-source. You need to specify the loopback interface as the source for BGP updates.
upvoted 0 times
Stefany
14 days ago
I agree with you, D) update-source is the correct answer for configuring the loopback as the BGP source.
upvoted 0 times
...
Marvel
15 days ago
No, I'm pretty sure it's D) update-source. That's what specifies the loopback interface.
upvoted 0 times
...
Tegan
30 days ago
Got it, so the two parameters that must be set in the BGP configuration are D) update-source and A) ebgp-enforce-multihop.
upvoted 0 times
...
Carylon
1 months ago
Are you sure about that? I think it's A) ebgp-enforce-multihop.
upvoted 0 times
...
Chauncey
1 months ago
Yes, that's correct. Another parameter that needs to be set is A) ebgp-enforce-multihop.
upvoted 0 times
...
Lili
1 months ago
I agree, D) update-source is needed to specify the loopback interface as the source for BGP updates.
upvoted 0 times
...
...
Shanda
2 months ago
I think the answer is D) update-source.
upvoted 0 times
...

Save Cancel
az-700  pass4success  az-104  200-301  200-201  cissp  350-401  350-201  350-501  350-601  350-801  350-901  az-720  az-305  pl-300  

Warning: Cannot modify header information - headers already sent by (output started at /pass.php:70) in /pass.php on line 77