Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions

CompTIA Exam 220-1101 Topic 2 Question 40 Discussion

Actual exam question for CompTIA's 220-1101 exam
Question #: 40
Topic #: 2
[All 220-1101 Questions]

A printer technician receives a support request for a laser printer that sometimes cuts off the bottom of the print job. During troubleshooting the technician notices that affected jobs are set for 8.5in x 14in (216mm x 356mm) paper and only print from a particular paper tray. Which of the following actions should the technician perform NEXT?

Show Suggested Answer Hide Answer
Suggested Answer: C

The IP address 192.168.1.56 is within the private IP address range (192.168.0.0 to 192.168.255.255) and is appropriate for use in an internal network utilizing NAT (Network Address Translation). The other IP addresses provided (172.15.65.10, 175.16.20.3, and 193.167.35.4) are either public IP addresses or not in the private IP range suitable for an internal network using NAT.


Contribute your Thoughts:

Milly
1 months ago
This is a classic case of 'when in doubt, check the settings.' Nothing beats a good old-fashioned triage, am I right? Let's leave the roller replacement to the professionals, shall we?
upvoted 0 times
Lovetta
15 days ago
D) Reset the default to use 8.5in x 11in (216mm x 279mm) paper
upvoted 0 times
...
Arlyne
22 days ago
A) Verify that the printing trays are correctly set.
upvoted 0 times
...
Frederick
23 days ago
B) Swap printer trays until the print jobs complete as expected.
upvoted 0 times
...
Dana
24 days ago
A) Verify that the printing trays are correctly set.
upvoted 0 times
...
...
Dolores
2 months ago
Resetting to 8.5x11? Nah, that's not gonna fix the problem. We need to address the issue with the 8.5x14 jobs specifically. Gotta keep our eye on the ball here, folks.
upvoted 0 times
Casie
9 days ago
I agree, we need to focus on the specific issue with the 8.5x14 jobs.
upvoted 0 times
...
Erick
11 days ago
C) Replace the tray rollers to ensure proper alignment.
upvoted 0 times
...
Lawrence
16 days ago
A) Verify that the printing trays are correctly set.
upvoted 0 times
...
...
Jess
2 months ago
Replace the tray rollers? Hmm, that's a bit drastic. I'd want to exhaust the simpler options before going that route. Verifying the settings is the logical first step in my book.
upvoted 0 times
...
Jarod
2 months ago
Swapping trays? That's just gonna create more problems. Let's start with the basics and check the tray configuration first. Wouldn't want to go down the wrong path and end up chasing our tails.
upvoted 0 times
Miesha
13 days ago
C) Replace the tray rollers to ensure proper alignment.
upvoted 0 times
...
Melvin
15 days ago
Yeah, let's make sure everything is configured correctly before we start swapping things around.
upvoted 0 times
...
Merlyn
23 days ago
That could also be a potential solution if the trays are set up correctly but the issue persists.
upvoted 0 times
...
Tiera
1 months ago
A) Verify that the printing trays are correctly set.
upvoted 0 times
...
Kallie
1 months ago
C) Replace the tray rollers to ensure proper alignment.
upvoted 0 times
...
Sonia
1 months ago
Good idea. Let's make sure everything is configured correctly before trying anything else.
upvoted 0 times
...
Mari
2 months ago
A) Verify that the printing trays are correctly set.
upvoted 0 times
...
...
Kallie
2 months ago
Okay, let's think this through. Since the issue only affects 8.5x14 jobs from a specific tray, I'd say verifying the tray settings is the way to go. Gotta make sure everything's dialed in properly.
upvoted 0 times
...
Nickole
2 months ago
I think swapping printer trays until the print jobs complete as expected could also be a good option.
upvoted 0 times
...
Kati
2 months ago
I agree with Ashlyn, checking the printing trays seems like the logical next step.
upvoted 0 times
...
Ashlyn
2 months ago
I think the technician should verify that the printing trays are correctly set.
upvoted 0 times
...

Save Cancel
az-700  pass4success  az-104  200-301  200-201  cissp  350-401  350-201  350-501  350-601  350-801  350-901  az-720  az-305  pl-300  

Warning: Cannot modify header information - headers already sent by (output started at /pass.php:70) in /pass.php on line 77
a