Free Preparation Discussions
MENU
Cisco 350-501 Exam Questions
- Cisco Certified Internetwork Expert CCIE Certifications
- Cisco Certified Internetwork Expert Service Provider CCIE Service Provider Certifications
- Cisco Certified Network Professional Service Provider CCNP Service Provider Certifications
- Topic 1: Describe service provider architectures: This section of the exam covers core architectures, Transport Technologies, Mobility, and Cisco network software architecture.
- Topic 2: Networking: This section of the exam covers implementing IPv4 and IPv6, route advertisement, area addressing, multi-topology, metrics, implementing OSPF, neighbor adjacency, route advertisement, multiarea, and metrics.
- Topic 3: MPLS and Segment Routing: This section of the exam covers implementing MPLS, describing traffic engineering, and segment routing.
- Topic 4: Services: This part of the exam comprises topics such as explaining VPN services, configuring L3VPN, and implementing multicast services.
- Topic 5: Automation and Assurance: This section of the exam covers the programmable APIs used to include Cisco devices in the network automation process.
Free Cisco 350-501 Exam Actual Questions
Note: Premium Questions for 350-501 were last updated On Apr. 24, 2025 (see below)
Which two PHY modes are available to implement an IOS XR Gigabit Ethernet interface interface? (Choose two.)
The available PHY modes to implement an IOS XR Gigabit Ethernet interface areMAN (Metropolitan Area Network)andWAN (Wide Area Network).Reference:
Cisco IOS XR Software Configuration Guide
Hr40wan - 10 Gigabit Ethernet WAN PHY Controller Commands on Cisco IOS XR
10-Gigabit Ethernet WAN PHY Controller Commands
Refer to the exhibit:
Router 1 was experiencing a DDoS attack that was traced to interface gjgabitethernet0/1.
Which statement about this configuration is true?
Refer to the exihibit.
Refer to the exhibit. Routers R1 through R5 are being deployed within the core of a service provider running BGP The core supports distribution of VPNv4 routes using MPLS. R3 currently has multiple paths to reach R4. A network engineer must implement BGP attributes so that R3 can reach R4 via R1. Which action must the engineer take to meet the requirement?
To direct traffic from R3 to R4 via R1, the weight attribute on R3 can be set higher for the route through R1 compared to other routes. Weight is a Cisco-specific BGP attribute that determines the preferred path when multiple routes to the same destination exist. It is local to the router on which it is configured and not advertised to other BGP peers.
Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) course materials.
Refer to the exihibit.
Refer to the exhibit. The operations team is implementing an LDP-based configuration in the service provider core network with these requirements:
R1 must establish LDP peering with the loopback IP address as its Router-ID.
Session protection must be enabled on R2.
How must the team update the network configuration to successfully enable LDP peering between R1 and R2?
- Select Question Types you want
- Set your Desired Pass Percentage
- Allocate Time (Hours : Minutes)
- Create Multiple Practice tests with Limited Questions
- Customer Support
Avery
3 hours agoJuan
20 hours agoBeckie
1 months agoLina
1 months agoTamra
2 months agoVeronika
2 months agoSue
2 months agoDoretha
3 months agoRosina
3 months agoTeri
3 months agoSunshine
3 months agoXochitl
4 months agoHuey
4 months agoKanisha
4 months agoHerminia
5 months agoJutta
5 months agoTalia
5 months agoNakita
5 months agoRaina
5 months agoRodolfo
6 months agoMicaela
6 months agoEmilio
6 months agoBlondell
6 months agoKati
6 months agoMelynda
7 months agoRodolfo
7 months agoJanessa
7 months agoLouann
7 months agoParis
8 months agoSherell
8 months agoRessie
8 months agoElden
8 months agoCarol
9 months agoCatherin
10 months agoFlorinda
10 months agoVirgie
10 months agoBarrett
10 months agoOwen
11 months agoMark james
12 months agoJeff K
11 months agoSmith K
12 months agoRobert K
12 months ago