Free Preparation Discussions
MENU
Cisco 300-710 Exam Questions
- Cisco Certified Network Professional CCNP Certifications
- Cisco Certified Network Professional Security CCNP Security Certifications
- Topic 1: Describe Rapid Threat Containment (RTC) Functionality Within Firepower Management Center/ Application Detectors (Open Appid)
- Topic 2: Configure These Policies In Cisco Firepower Management Center/ Implement NGFW Modes
- Topic 3: Configure System Settings In Cisco Firepower Management Center/ Describe IRB Configurations
- Topic 4: Configure Devices Using Firepower Management Center/ Implement High Availability Options
- Topic 5: Configure These Features Using Cisco Firepower Management Center/ Management And Troubleshooting
- Topic 6: Troubleshoot Using Packet Capture Procedures/ Implement NGIPS Modes
- Topic 7: Describe Cisco FMC Pxgrid Integration With Cisco Identify Services Engine (ISE)/ Troubleshoot With FMC CLI And GUI
- Topic 8: Describe Using Cisco Threat Response For Security Investigations/ Active/Standby Failover
- Topic 9: Implement Threat Intelligence Director For Third-Party Security Intelligence Feeds/ Analyze Risk And Standard Reports
- Topic 10: Configure Cisco AMP For Endpoints In Firepower Management Center/ Configure Dashboards And Reporting In FMC
- Topic 11: Configure Cisco AMP For Networks In Firepower Management Center/ Configure Objects Using Firepower Management Center
Free Cisco 300-710 Exam Actual Questions
Note: Premium Questions for 300-710 were last updated On Apr. 25, 2025 (see below)
What is an advantage of adding multiple inline interface pairs to the same inline interface set when deploying an asynchronous routing configuration?
An engineer is troubleshooting a device that cannot connect to a web server. The connection is initiated from the Cisco FTD inside interface and attempting to reach 10.0.1.100 over the non-standard port of 9443 The host the engineer is attempting the connection from is at the IP address of 10.20.10.20. In order to determine what is happening to the packets on the network, the engineer decides to use the FTD packet capture tool Which capture configuration should be used to gather the information needed to troubleshoot this issue?
A)
B)
C)
D)
Refer to the exhibit.
A company is deploying a pair of Cisco Secure Firewall Threat defence devices named FTD1 and FTD2. FTD1 and FTD2 have been configured as an active/standby pair with a failover link but without a stateful link. What must be implemented next to ensure that users on the internal network still communicate with outside devices if FTD1 fails?
In a failover configuration with Cisco Secure Firewall Threat Defense (FTD) devices, ensuring that users on the internal network can continue to communicate with outside devices if the primary device (FTD1) fails requires the implementation of a stateful failover link. The stateful failover link allows the secondary device (FTD2) to maintain session information and state data, ensuring seamless failover and minimizing disruptions.
Steps to implement a stateful failover link:
Physically connect a stateful failover link between FTD1 and FTD2.
Configure the stateful failover link in the FMC.
Ensure that both devices are properly synchronized and that stateful failover is enabled.
Deploy the changes to both FTD devices.
By configuring a stateful link, the secondary FTD can take over active sessions without requiring users to re-establish their connections, thus ensuring continuous communication.
An engineer is troubleshooting application failures through a FTD deployment. While using the FMC CLI. it has been determined that the traffic in question is not matching the desired policy. What should be done to correct this?
A network administrator wants to configure a Cisco Secure Firewall Threat Defense instance managed by Cisco Secure Firewall Management Center to block traffic to known cryptomning networks. Which system settings must the administrator configure in Secure Firewall Management Center to meet the requirement?
To block traffic to known cryptomining networks using Cisco Secure Firewall Threat Defense (FTD) managed by Cisco Secure Firewall Management Center (FMC), the network administrator needs to configure Security Intelligence in an Access Control Policy. Security Intelligence allows administrators to block traffic based on threat intelligence feeds, which include known malicious IP addresses, domains, and URLs.
Steps:
Navigate to Policies > Access Control > Access Control Policy in FMC.
Edit or create an Access Control Policy.
Go to the Security Intelligence tab.
Enable the relevant threat intelligence feeds that include cryptomining networks.
Apply the policy to the FTD device.
This configuration ensures that traffic to known cryptomining networks is blocked, enhancing the network's security posture against cryptomining threats.
- Select Question Types you want
- Set your Desired Pass Percentage
- Allocate Time (Hours : Minutes)
- Create Multiple Practice tests with Limited Questions
- Customer Support
Micah
3 hours agoElden
1 months agoElise
1 months agoLyda
2 months agoGiovanna
2 months agoCordelia
2 months agoHoa
3 months agoShannan
3 months agoCarin
3 months agoYasuko
3 months agoKristofer
4 months agoGayla
4 months agoAmira
4 months agoMarlon
5 months agoMy
5 months agoMerri
5 months agoChuck
5 months agoLenna
5 months agoBuddy
6 months agoAshley
6 months agoRory
6 months agoRyan
6 months agoBobbye
6 months agoSylvie
7 months agoLucille
7 months agoFletcher
7 months agoMickie
7 months agoJustine
7 months agoCandra
8 months agoLezlie
8 months agoMaryann
8 months agoSilva
8 months agoKristofer
9 months agoFiliberto
9 months agoFrancesco
10 months agoVerda
10 months agoAnisha
10 months agoFelix
11 months ago