Independence Day Deal! Unlock 25% OFF Today – Limited-Time Offer - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions

Cisco Exam 300-710 Topic 8 Question 68 Discussion

Actual exam question for Cisco's 300-710 exam
Question #: 68
Topic #: 8
[All 300-710 Questions]

An engineer is implementing a new Cisco Secure Firewall. The firewall must filler traffic between the three subnets:

* LAN 192.168.101.0724

* DMZ 192.168 200.0/24

* WAN 10.0.0.0/30

Which firewall mode must the engineer implement?

Show Suggested Answer Hide Answer
Suggested Answer: C

https://www.cisco.com/c/en/us/td/docs/security/firepower/640/configuration/guide/fpmc-config-guide-v64/system_configuration.html#ID-2241-00000551

''You cannot send backups to one remote system and reports to another, but you can choose to send either to a remote system and store the other on the Firepower Management Center.''


Contribute your Thoughts:

Mirta
1 months ago
I'm going with C) routed mode. It just makes the most sense based on the requirements in the question. Plus, I heard routed mode is the most common configuration for Cisco firewalls these days.
upvoted 0 times
Leota
1 days ago
I agree, routed mode is probably the way to go for this setup.
upvoted 0 times
...
Elza
6 days ago
Routed mode does seem like the most logical option based on the subnets mentioned.
upvoted 0 times
...
Micah
16 days ago
I think C) routed mode is the best choice too. It's the most common configuration for Cisco firewalls.
upvoted 0 times
...
...
Tonja
2 months ago
Ha, this is a tricky one! I bet the answer is C) routed mode, just to make us think. Cisco firewalls are like little traffic cops, gotta keep those packets moving in the right direction, am I right?
upvoted 0 times
Joseph
20 days ago
Definitely, Cisco firewalls are all about directing traffic in the right direction. Routed mode is the way to go.
upvoted 0 times
...
Yasuko
22 days ago
Yeah, I agree. Routed mode would be the most appropriate for handling traffic between different networks.
upvoted 0 times
...
Candra
1 months ago
I think you're right, C) routed mode sounds like the best choice for filtering traffic between those subnets.
upvoted 0 times
...
...
Katheryn
2 months ago
I'm not sure about this one. Maybe B) network mode would work since it's a Cisco Secure Firewall? I'm still learning the different firewall modes, so I'll have to do some more research.
upvoted 0 times
Beula
5 days ago
User1: It's possible, but I think routed mode would provide better control over the traffic flow.
upvoted 0 times
...
Rodolfo
19 days ago
User3: I'm not sure, but maybe A) transparent mode could also work for this scenario.
upvoted 0 times
...
Fletcher
27 days ago
User2: I agree, routed mode would be a good choice for the Cisco Secure Firewall implementation.
upvoted 0 times
...
Blondell
1 months ago
User1: I think C) routed mode might be the best option for filtering traffic between the subnets.
upvoted 0 times
...
...
Richelle
2 months ago
I think the correct answer is C) routed mode. The question mentions that the firewall must filter traffic between three different subnets, so it needs to be in routed mode to handle the routing between them.
upvoted 0 times
Yvette
2 months ago
Yes, I think C) routed mode is the best choice for this scenario.
upvoted 0 times
...
Elise
2 months ago
I agree, C) routed mode makes sense because it can handle routing between different subnets.
upvoted 0 times
...
...
Jose
2 months ago
I'm not sure, but I think gateway mode could also work since it acts as a bridge between different networks.
upvoted 0 times
...
Alverta
2 months ago
I agree with Markus. Routed mode makes sense for filtering traffic between different subnets.
upvoted 0 times
...
Markus
3 months ago
I think the engineer should implement firewall mode C) routed.
upvoted 0 times
...

Save Cancel
az-700  pass4success  az-104  200-301  200-201  cissp  350-401  350-201  350-501  350-601  350-801  350-901  az-720  az-305  pl-300  

Warning: Cannot modify header information - headers already sent by (output started at /pass.php:70) in /pass.php on line 77