Free Cisco 300-410 Exam Dumps and 300-410 Exam Questions

Question No: 31

MultipleChoice

Refer to the exhibit.

Refer to the exhibit. The DHCP client is unable to receive an IP address from the DHCP server RouterB is configured as follows:

Interface fastethernet 0/0

description Client DHCP ID 394482431

Ip address 172 31 11 255 255.255 0

!

ip route 172.16.1.0 255 255 255.0 10.1.1.2

Which command is required on the fastethernet 0/0 interface of RouterB to resolve this issue?

Options

ARouterB(config-if)#lp helper-address 172.31.1.1

BRouterBiconfig-ififclp helper-address 255.255 255 255

CRouterB(config-if)#lp helper-address 172.16.1.1

DRouterB(config-if)#lp helper-address 172.16.1.2

Question No: 32

MultipleChoice

An engineer sets up a DMVPN connection to connect branch 1 and branch 2 to HQ branch 1 and branch 2 cannot communicate with each other. Which change must be made to resolve this issue?

Options

AOption A

BOption B

COption C

DOption D

Question No: 33

MultipleChoice

Refer to the exhibit. R2 has two paths to reach 192.168.13.0/24. but traffic is sent only through R3. Which action allows traffic to use both paths?

Options

AConfigure the bandwidth 2000 command under interface FastEthernet0/0 on R2.

BConfigure the variance 4 command under the EIGRP process on R2.

CConfigure the delay 1 command under interface FastEthernet0/0 on R2.

DConfigure the variance 2 command under the EIGRP process on R2

Question No: 34

MultipleChoice

Refer to the exhibit. an engineer is trying to get 192.168.32.100 forwarded through 10.1.1.1, but it was forwarded through 10.1.1.2. What action forwards the packets through 10.1.1.1?

Options

AConfigure EIGRP to receive 192.168.32.0 route with lower admin distance.

BA. Configure EIGRP to receive 192.168.32.0 route with longer prefix than /19.

CA. Configure EIGRP to receive 192.168.32.0 route with lower metric.

DA. Configure EIGRP to receive 192.168.32.0 route with equal or longer prefix than /24.

Question No: 35

DragDrop

Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right.

Same Answer is already updated below:

Question No: 36

MultipleChoice

Exhibit:

Refer to the exhibit. an engineer is trying to get 192.168.32.100 forwarded through 10.1.1.1, but it was forwarded through 10.1.1.2. What action forwards the packets through 10.1.1.1?

Options

AConfigure EIGRP to receive 192.168.32.0 route with lower admin distance.

BA. Configure EIGRP to receive 192.168.32.0 route with longer prefix than /19.

CA. Configure EIGRP to receive 192.168.32.0 route with lower metric.

DA. Configure EIGRP to receive 192.168.32.0 route with equal or longer prefix than /24.

Question No: 37

MultipleChoice

Refer to the exhibit.

The Math and Science departments connect through the corporate IT router but users in the Math department must not be able to reach the Science department and vice versa Which configuration accomplishes this task?

Options

Avrf definition Science

interface E 0/2
ip address 192.168.1.1 255.255.255.0
no shut

interface E 0/3
ip address 192.168.2.1 255.255.255.0
no shut

Bvrf definition Science
address-family ipv4
!
interface E 0/2
ip address 192.168.1.1 255.255.255.0
vrf forwarding Science
no shut
!
interface E 0/3
ip address 192.168.2.1 255.255.255.0
vrf forwarding Science
no shut

Cvrf definition Science
address-family ipv4
!
interface E 0/2
ip address 192.168.1.1 255.255.255.0
no shut
!
interface E 0/3
ip address 192.168.2.1 255.255.255.0
no shut

Dvrf definition Science
address-family ipv4
!
interface E 0/2
vrf forwarding Science
ip address 192.168.1.1 255.255.255.0
no shut
!
interface E 0/3
vrf forwarding Science
ip address 192.168.2.1

Question No: 38

MultipleChoice

Refer to the exhibit. The administrator configured route advertisement to a remote low resources rooter to use only the default route to reach any network but failed. Which action resolves this issue?

Options

AChange the direction of the distribute-list command from out to in.

BRemove the line with the sequence number 5 from the prefix list.

CRemove the prefix keyword from the distribute-list command.

DRemove the line with the sequence number 10 from the prefix list.

Question No: 39

MultipleChoice

Refer to the exhibits.

When DMVPN is configured, which configuration allows spoke-to-spoke communication using loopback as tunnel source?

Options

AConfigure crypto isakmp key cisco address 0.0.0.0 on the hub.

BConfigure crypto isakmp key Cisco address 200.1.0.0 255.255.0.0 on the hub.

CConfigure crypto isakmp key cisco address 200.1.0.0 255.255.0.0 on the spokes.

DConfigure crypto isakmp key cisco address 0.0.0.0 on the spokes.