Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location PL
Mob_nav_barsMENU

CheckPoint Exam 156-582 Topic 4 Question 6 Discussion

Actual exam question for CheckPoint's 156-582 exam
Question #: 6
Topic #: 4
[All 156-582 Questions]

How do you verify that Proxy ARP entries are loaded into the kernel?

Show Suggested Answer Hide Answer
Suggested Answer: A

The fw ctl arp command is used to verify that Proxy ARP entries are loaded into the kernel. This command provides detailed information about the current ARP table, including any Proxy ARP entries that have been established for NAT configurations. Ensuring that these entries are present confirms that the system is correctly handling ARP requests for NATed addresses.


by Bettye at Jan 09, 2025, 04:20 AM

Limited Time Offer

25%

Off

Get Premium 156-582 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel
Percy
2 months ago
Proxy ARP? More like Proxy ARG, amirite? But seriously, I'll go with D. It seems the most comprehensive option.
upvoted 0 times
...
Shawnee
2 months ago
I'm going to have to disagree with Stephanie. 'fw ctl arp' sounds like it could be a real command. But I think D is the best choice here.
upvoted 0 times
...
Stephanie
2 months ago
Haha, the 'fw ctl arp' option sounds like it's straight out of a sci-fi movie. I'm going with D, it's the most technical-sounding one.
upvoted 0 times
Dominga
1 months ago
User 4: I prefer using 'show arp dynamic all' to verify Proxy ARP entries.
upvoted 0 times
...
Andree
1 months ago
User 3: I usually check the logs for Proxy ARP entries.
upvoted 0 times
...
Beatriz
1 months ago
User 2: I'm going with option D, 'fw ctl get arp list all'.
upvoted 0 times
...
Jenifer
1 months ago
I agree, option D sounds like the most technical choice.
upvoted 0 times
...
Una
2 months ago
I'm going with option D, 'fw ctl get arp list all'.
upvoted 0 times
...
Shantell
2 months ago
User 1: I think 'fw ctl arp' is the way to go.
upvoted 0 times
...
Marshall
2 months ago
I prefer 'show arp dynamic all' for checking Proxy ARP entries.
upvoted 0 times
...
Chara
2 months ago
I think 'fw ctl arp' is the way to go.
upvoted 0 times
...
...
Rebbeca
3 months ago
C seems like the most straightforward answer to me. The logs should have the Proxy ARP entries under the NAT section.
upvoted 0 times
...
Rory
3 months ago
I think D is the way to go. You can use the 'fw ctl get arp list all' command to see all the ARP entries, including the Proxy ARP ones.
upvoted 0 times
Simona
2 months ago
I usually use 'fw ctl arp' to verify Proxy ARP entries in the kernel.
upvoted 0 times
...
Juan
2 months ago
I agree, 'fw ctl get arp list all' is the command to check Proxy ARP entries.
upvoted 0 times
...
...
Karima
3 months ago
I'm not sure, but I think D) fw ctl get arp list all might also be a valid option to verify Proxy ARP entries.
upvoted 0 times
...
Celestine
4 months ago
I agree with Stanton, because fw ctl arp is used to manage ARP entries in the kernel.
upvoted 0 times
...
Stanton
4 months ago
I think the answer is A) fw ctl arp.
upvoted 0 times
...

Save Cancel
az-700  pass4success  az-104  200-301  200-201  cissp  350-401  350-201  350-501  350-601  350-801  350-901  az-720  az-305  pl-300  

Warning: Cannot modify header information - headers already sent by (output started at /pass.php:70) in /pass.php on line 77